MODEL. . . . . . . . . . . . . . . . . . . . . 210 A/13
SERIAL . . . . . . . . . . . . . . . . . . . . FF 2549
TONNAGE. . . . . . . . . . . . . . . .  . . 55
LENGTH OF KNIFE . . . . . . . . . . . .10″
FLATS . . . . . . . . . . . . . . . . . . . . . 6″ X 5/8″ OR 8″ X 1/2″
ANGLES – 90 DEGREES . . . . . . . . 4″ X 4″ X 1/2″
             - 45 DEGREES . . . . . . . . 3-1/2″ X 3-1/2″ X 5/16″
TEES – 90 DEGREES . . . . . . . . . . 4″ X 4″ X 3/8″
         – 45 DEGREES . . . . . . . . . . 3″ X 3″ X 3/8″
CHANNELS – 90 DEGREES. . . . . . 5″ X 5″ X 1/2″
ROUNDS. . . . . . . . . . . . . . . . . . . 1-5/8″
SQUARES. . . . . . . . . . . . . . . . . . 1-1/2″
NOTCHER – PLATES. . . . . . . . . . 7/16″
                – ANGLES & TEES. . . .3″ X 3/8″
PUNCHING. . . . . . . . . . . . . . . . . 1″ X 5/8″
SPEED. . . . . . . . . . . . . . . . . . . . .37 SPM
MOTOR . . . . . . . . . . . . . . . . . . . .5 HP
ELECTRICS . . . . . . . . . . . . . . . . .440/60/3 VOLT
WEIGHT. . . . . . . . . . . . . . . . . . . .2,500 LBS
DIMENSIONS . . . . . . . . . . . . . . . 40″ W X 57″ D X 82″ H
C/W:
- QUANTITY OF PUNCHES & DIES;
- PUNCH HOLDERS & TOOLS;
  

MODEL. . . . . . . . . . . . . . . . . . . . . .2D
SWING OVER CROSS SLIDE. . . . . .7-1/8″
SWING UNDER SUPPORT BAR . . . .9″
SPINDLE HOLE. . . . . . . . . . . . . . . .1-11/16″
SPINDLE BAR CAPACITY. . . . . . . . 1-5/8″
SPINDLE SPEEDS (16). . . . . . . . . .50 – 2,550 RPM
MAX. DISTANCE TO CAPSTAN . . . .18-3/4″
MANUAL CAPSTAN STROKE . . . . . .7-5/8″
NUMBER OF TURRET HOLDERS. . . .6
ELECTRICS. . . . . . . . . . . . . . . . . . .440/60/3 VOLT
SPINDLE DRIVE . . . . . . . . . . . . . . .2-1/2 HP
DIMENSIONS . . . . . . . . . . . . . . . . .87″ L X 37″ W X 52″ H
WEIGHT . . . . . . . . . . . . . . . . . . . . .2,200 LBS
C/W:
- 14 COLLETS – FROM 5/8″ – 1-1/2″ RD & A FEW HEX SIZES;
- SQUARE TOOL POST ON FRONT & REAR TOOL POST;
- KNURLING TOOLS, DIE HEAD & CHASERS, BRING BAR HOLDER,
  DIE & TAP HOLDERS, DRILL CHUCKS, ASSORTED TOOLING.